What machines are needed for light pole production

What machines are needed for light pole production

You may be used to the street lights that can be seen everywhere on the road. However, it is not that simple to manufacture street light poles. It requires a complete light pole production line. Fortunately, this production line is also suitable for sign poles. , flagpole, high pole lamp production, if you have the need to produce these products, you can learn about this lamp pole production line.

The light pole production line is mainly composed of a simple rolling and flattening production line, a steel plate oblique shearing production line, a double sheet metal bending machine, an automatic seam welding production line, a mechanical seam seam machine, a semi-automatic welding production line, a steel pipe straightening machine, and a pipe bending machine.

Of course, these machines are not irreplaceable for you. For example, the simple rolling and flattening production line and the steel plate oblique shearing production line can be replaced by cutting machines + labor. For specific machines, you can consult us through the contact information on the website, and adjust according to your actual situation and budget. Only the most representative processing methods are introduced here.

The main function of each machine is described below

Simple rolling and flattening production line

It is mainly to unwind, flatten and cut the steel coil into the required size. The system consists of six parts, such as uncoiler and side guide device, flattening machine, shearing device, yard bar, and electrical system. It is especially suitable for the opening and leveling of pole material equipment such as street lamp poles and flagpoles.

Steel plate oblique shearing production line

It is suitable for longitudinal shearing of long shearing plates, and the length of shearing plates can be adjusted arbitrarily. With high labor productivity, the plate to be cut is pressed on the traveling device by hydraulic steel, and the disc knife is rotated and sheared, and the plate is cut with the operation of the traveling device. If the size is required to be placed obliquely, the tapered plate can be cut. It is especially suitable for the cutting of light poles and flagpoles.

Double sheet bending machine

The equipment consists of two bending machines, which are linked in two stages to achieve synchronous work. They are randomly equipped with different lamp pole molds, which can be applied to the production of street lamp poles, flag poles, high pole lamps, etc. It is used in the production of conical lamp poles. , Install the conical mold, bend it with multiple knives, and bend the middle of the last knife, and a conical light pole is formed. Then use the light pole rolling machine to pull out the light pole; when you need to produce polygonal light poles, sign poles and high pole lights, install a polygonal special mold, bend with multiple knives, and finally bend the middle knife with one knife, a multi-deformable light pole It is formed, and then the light rod is pulled out with a rod rounder.

Automatic seam welding production line

The equipment consists of a main machine head, a traction bed, and a servo material discharge cover. The traction bed is clamped by the traction chuck on the sports trolley to move the steel big-end trolley, and push the steel rod to move from the small head to the big head. Six clamps on the main head The claw moves at a constant speed, and the big end of the steel rod is hijacked by the loose steel rod trolley, and the guide wheel on the machine head realizes automatic seam alignment. When the steel rod is seamed, the welding machine starts to undulate and weld. , The flux is automatically recovered, the welding seam is uniform, continuous and beautiful, the penetration is strong, the seam welding is formed at one time, the welding efficiency is high, the speed is 23 m/min, which is 3 times that of the gas shielded welding, and the cost is lower than that of the gas welding. The equipment with the fastest welding speed, good effect and the lowest price in the industry. This equipment mainly welds street lamp poles and flagpoles, and the sign poles and high pole lights with relatively large poles generally do not need this equipment. Sign poles and high pole lights with relatively large poles generally do not use this equipment.

Mechanical sewing machine

This machine is a special equipment suitable for high pole lights and sign poles to be seamed after bending. The machine is driven by a turbine and a worm, and can be operated in linkage or single action. It can be operated with manual electric welding. It has high efficiency. After spot welding is finalized, it is welded on the semi-automatic welding production line. Do a full circle.

Semi-automatic welding production line

The machine does not emit light, and the welding speed is fast. It is suitable for all kinds of rod bodies. It is convenient and quick to adjust manually. The welding seam is uniform, continuous and beautiful, and the penetration is strong. It is the necessary equipment for the sign pole after the mechanical sewing machine is seamed, and the welding of the high pole lamp.

Steel pipe straightening machine

The structure of the equipment is simple, compact and convenient. During the specific operation, the steel rod can be manually placed on the die, and there are individuals who hold it, hold it by hand, and press the button to press the button. The straightness of the steel pole is controlled by manual visual inspection, and the efficiency is high. The equipment can straighten any shape of street light poles, sign poles, flagpoles and high pole lights, and the head is full circle.

Bender

According to the design requirements, the head of some street light poles needs to be bent, that is, the self-bending arm street light pole, which is composed of a main board and a bending die. Equipped with two sets of molds, the straight mold is cleaned by the reducer, and the steel pipe pressed on the round mold is bent along the round mold. The operation is simple, no heating and fillers are required, and the upper part of the tapered street light pole can be bent directly, which is economical and affordable. Essential equipment for rod manufacturers.

Through the above procedures, a street lamp pole is basically formed, and then the lamp gate is cut out with a plasma cutting machine, and round or square flanges are welded according to the requirements of the drawings. Finally, the light pole is polished, and a beautiful and beautiful light pole is completed.

If you have the need to manufacture light poles, you can contact us through the website at any time, and we will reply as soon as we see it.